ELECTRICAL SYSTEMS
The MRS range offers three purpose-built electrical systems, each providing a different level of vehicle integration, functionality and construction. Choose the system that best suits your requirements.
The MRS range offers three purpose-built electrical systems, each providing a different level of vehicle integration, functionality and construction. Choose the system that best suits your requirements.
Factory-integrated rotary loom
What it covers
- Engine-side TXL harness with Deutsch DT vehicle integration connector on the right-hand side
- Separate distributor harness. Separate fuel pump and fan harness with integrated relay and fuse assembly for mounting at the front right-hand side of the engine bay.
- Bulkhead plate and 90° boot; labelled circuits for ignition, charging, starting, gauges and reverse
Vehicle connections
Uses the vehicle’s existing ignition, starter and alternator relay/fuse arrangements.
Engine harness connections
Connect the following vehicle circuits through the supplied engine-bay Deutsch DT connector:
- ignition and starter relay outputs,
- alternator sense (S) and charge warning lamp (L),
- both reverse switch wires,
- factory water temperature gauge and
- factory oil pressure warning light.
- rev counter
Vehicle-side terminal crimping is required. Refer to the installation instructions for wiring and pin locations.
Fuel pump and fan harness connections
Connect the relay/fuse assembly at the front right-hand side of the engine bay
- to a direct battery feed, fused close to the battery.
- Connect its earth lead preferably to battery negative, or to a suitable clean, bare-metal chassis earth point.
Aftermarket gauge connections
Power, earth and sender signal wiring for the aftermarket gauges is already integrated into the harness. Connect gauge illumination separately to the vehicle’s lighting switch circuit.
- oil pressure
- oil temperature
- water temperature
Refer to the installation instructions for wiring details.
NZ$1,200
Standalone rotary harness
What it covers
- Complete harness built with TXL wire, expandable braid sheathing and glue-lined heat shrink.
- Standalone electrical system with an under-dash mounted fuse and relay box, firewall bulkhead plate and boot.
- Complete harness built with TXL wire, expandable braid sheathing and glue-lined heat shrink.
- Standalone electrical system with an under-dash mounted fuse and relay box, firewall bulkhead plate and boot.
Vehicle connections
A standalone engine electrical system requiring four primary vehicle connections to get the engine running.
Primary vehicle connections
- Battery Main — +12 V
- Earth — negative (−)
- Key ON — +12 V
- Key START — +12 V while cranking
Additional vehicle connections
Additional connections are provided for:
- rev counter
- factory water temperature gauge
- factory oil pressure warning light
- charge warning lamp
- both reverse switch wires
Aftermarket gauge connections
Power, earth and sender signal wiring for the aftermarket gauges is already integrated into the harness. Connect gauge illumination separately to the vehicle’s lighting switch circuit.
- oil pressure
- oil temperature
- water temperature
Refer to the installation instructions for wiring details.
NZ$2,200
Motorsport construction
What it covers
- Performance system architecture with Tefzel wire and Raychem DR25 covering
- Concentric twisting
- Motorsport circular bulkhead connector; separate distributor harness
- Standalone fuses and relays, fuel-pump and twin-fan control
Vehicle connections
A standalone engine electrical system requiring four primary vehicle connections to get the engine running.
Primary vehicle connections
- Battery Main — +12 V
- Earth — negative (−)
- Key ON — +12 V
- Key START — +12 V while cranking
Additional vehicle connections
Additional connections are provided for:
- rev counter
- factory water temperature gauge
- factory oil pressure warning light
- charge warning lamp
- both reverse switch wires
Aftermarket gauge connections
Power, earth and sender signal wiring for the aftermarket gauges is already integrated into the harness. Connect gauge illumination separately to the vehicle’s lighting switch circuit.
- oil pressure
- oil temperature
- water temperature
Refer to the installation instructions for wiring details.
NZ$3,000
INCLUDED WITH EVERY SYSTEM
- Fully terminated and clearly labelled — supplied with the required plugs and connectors, with every branch and connection labelled for simple installation.
- Separate coil-to-distributor harness — included with all three stages.
- Engine wiring and controls — the essential engine wiring — fuel-pump control and twin-fan control.
- Aftermarket gauge provisions — connections for oil pressure, oil temperature and water temperature gauges.
- Factory cluster connections — provisions for the required factory cluster functions.
Simpler installation
A complete, organised electrical solution takes the complexity out of rotary electrical installation, without needing to design and assemble individual circuits during your build.
Engine configuration at checkout
Select your alternator position, distributor type and water-pump type during checkout so your system can be supplied to suit your engine configuration.




