Magician Race SolutionsINSTALLATION GUIDE

Stage 1 Street Full Installation Guide

MRS Installation Instruction Quick Start Guide

MAGICIAN RACE SOLUTIONS

Stage 1 Street - Quick Start installation sequence.

Quick Start

Use this page as the installation sequence. The full instructions explain each step in more detail.

  1. Identify your four primary vehicle integration connections: Battery Main power, constant 12V positive; Earth, battery negative; Key ON signal, switched 12V positive, present with ignition on and during cranking; and Key START signal, 12V positive only while the key is held in START.
  2. Disconnect the negative battery terminal before beginning any wiring work.
  3. Identify the main engine harness, coil-to-distributor subloom, separate fan and fuel-pump harness with integrated fuse/relay assembly, and alternator charge cable.
  4. Identify the vehicle ignition, starter and instrument-cluster circuits using the correct vehicle wiring information.
  5. Mount the fully prewired fuse/relay assembly at the front right-hand side of the engine bay, securely and clear of excessive heat and water.
  6. Connect labeled main battery power and earth. Fit the main battery fuse close to the battery, with rating and arrangement per the approved schematic.
  7. Lay the engine harness along the contours of the engine, using labeled branches and plugs as guides; secure clear of heat and moving parts.
  8. Route the combined cabin section through the firewall grommet; gauge, cluster, fan-override and fuel-pump wiring are integrated.
  9. Connect labeled engine-side plugs, including the alternator L/S connector (S circuit protected by a 5 A fuse), starter trigger, senders and reverse switch.
  10. Install the separate alternator charge cable from alternator B+ to the starter battery-positive stud; secure and protect its routing.
  11. Install the coil-to-distributor subloom and connect both coils and the distributor.
  12. Route fan and fuel-pump branches. Terminate supplied mating 2-pin Deutsch DT plugs onto component wires and connect, checking polarity.
  13. Connect the vehicle integration DT plug, cabin manual fan override switch, automatic fan temperature switch, gauges and factory cluster circuits.
  14. With the battery disconnected, check connector seating, continuity, absence of shorts, fuse ratings, power/earth and ignition/starter wiring against the schematic.
  15. Reconnect battery. Key ON without cranking: confirm 12 V at both coil positives, charge and oil warning lamps illuminated, and gauges powered.
  16. With starter solenoid trigger disconnected, confirm 12 V at the trigger only while key is held in START; key OFF and reconnect.
  17. Start engine; confirm oil and charge warning lamps extinguish and tachometer responds. Test manual and automatic fan switching; verify both fans spin correctly.
  18. Verify fuel pump runs with key ON and stops with key OFF. Warm engine stationary, check instruments and charging voltage, then key OFF and recheck harness security.

IMPORTANT

Do not rely on wire colour alone when integrating the MRS system into the vehicle. Identify factory circuits using the correct vehicle wiring information and confirm electrically where practical.

Full Installation Instructions

Stage 1 Street | Detailed installation and electrical commissioning

1. Identify vehicle integration connections

Identify your four primary vehicle integration connections: Battery Main power, constant 12V positive; Earth, battery negative; Key ON signal, switched 12V positive, present with ignition on and during cranking; and Key START signal, 12V positive only while the key is held in START.

2. Preparation and safety

  1. Disconnect the negative battery terminal.
  2. Identify the main engine harness, coil-to-distributor subloom, separate fuel-pump and cooling-fan harness with its integrated, fully prewired fuse/relay assembly, and alternator charge cable.
  3. Identify the vehicle's ignition, starter and instrument-cluster circuits using the correct vehicle wiring information. Do not rely on wire colour alone.

3. Fuse and relay assembly

  1. Mount the fuse and relay assembly at the front right-hand side of the engine bay. Ensure it is secure, accessible and protected from excessive heat and water.
  2. Connect labeled main battery power and earth to the corresponding connection points. Install the main battery fuse close to the battery, using the rating and connection arrangement shown in the approved schematic.

4. Engine harness installation

  1. Lay the main engine harness along the contours of the engine, using the labeled branches and plugs as your guide. Route each labeled branch to its component and secure clear of heat and moving parts.
  2. Route the combined cabin section through the firewall grommet. The cluster, aftermarket gauges, manual fan override and fuel-pump wiring travel together in this harness; their lengths are preset.
  3. Connect engine components using their corresponding labeled plugs and connectors, including the starter trigger, senders and gearbox reverse-light switch.
  4. Connect the alternator L and S wires using the supplied alternator connector. The S circuit is protected by a 5-amp fuse as specified in the schematic.
  5. Install the supplied alternator charge cable from the alternator B+ terminal to the starter motor battery-positive stud. Secure both connections and route the cable clear of heat, sharp edges and moving parts.
  6. Install the coil-to-distributor subloom, connecting both ignition coils and the distributor. Secure it clear of heat and moving parts.

5. Cooling fan and fuel-pump harness

  1. Route the cooling-fan and fuel-pump branches from the engine-bay fuse/relay assembly to their components. Secure them away from heat, sharp edges and moving parts.
  2. For each cooling fan, crimp the supplied mating two-pin Deutsch DT connector onto the fan wires, checking polarity, then connect it to the preterminated harness plug.
  3. Crimp the supplied mating two-pin Deutsch DT connector onto the fuel-pump wires, checking polarity, then connect and secure the branch.

6. Vehicle integration and instruments

  1. Connect the supplied Deutsch DT vehicle-integration plug to the matching vehicle circuits, including Key ON and Key START, according to the supplied schematic.
  2. Connect the gearbox reverse-light switch through its labeled two-pin Deutsch DT plug and connect the corresponding vehicle-side reverse-light wiring to the vehicle's existing reverse-lamp circuit as shown in the schematic.
  3. Mount a customer-supplied ON/OFF manual cooling-fan override switch in the cabin and connect the two labeled wires already included in the cabin harness. This is an earth-switched control circuit; do not apply +12 V to the trigger wires.
  4. Connect the automatic temperature switch to its corresponding engine-bay harness connector; secure the branch clear of heat and moving parts.
  5. Connect aftermarket gauge power, earth and each labeled sender wire to the matching gauge.
  6. Connect labeled factory cluster wires to the water-temperature gauge, oil-pressure warning lamp, alternator charge warning lamp and tachometer. Confirm gauge/sender compatibility.

7. Pre-start electrical checks

  1. With the battery still disconnected, confirm all plugs and connectors are fully seated and secure.
  2. Check continuity, main power and earth connections, and verify there are no unintended short circuits. Do not perform continuity testing on live circuits.
  3. Confirm fuse ratings and locations against the approved schematic, and verify ignition and starter wiring against the vehicle wiring information.

8. Initial power-up

  1. Reconnect the battery. Turn the key ON without cranking.
  2. Confirm 12 volts at both ignition-coil positive terminals.
  3. Confirm the alternator charge warning lamp and oil-pressure warning lamp illuminate, and aftermarket gauges power up. If coil voltage is incorrect, stop and troubleshoot before proceeding.

9. Starter verification and first start

  1. Place the vehicle in neutral or park and apply the handbrake. Turn ignition OFF and disconnect the starter-solenoid trigger wire so the engine cannot crank during the test.
  2. Measure between the disconnected starter trigger wire and earth. Turn key to START and confirm 12 volts is present only in the START position. Turn key OFF, then reconnect the trigger.
  3. Start the engine. Confirm the oil-pressure warning lamp and alternator charge warning lamp extinguish and the tachometer responds correctly.

10. Cooling fan and fuel-pump testing

  1. Operate the manual fan override. Confirm both fans run and spin in the correct direction. Switch override OFF; the fans should stop if the automatic temperature switch is not calling for cooling.
  2. Allow the engine to warm and confirm the automatic temperature switch turns both fans on and subsequently off as temperature falls. Fan trigger wires are earth-switched only; do not apply +12 V.
  3. With ignition ON, confirm the fuel pump runs continuously. With ignition OFF, confirm it stops. If incorrect, inspect fuse, relay, earth and wiring against the schematic.

11. Final commissioning

  1. Warm the engine while stationary. Monitor instruments, verify charging voltage and confirm correct fan operation.
  2. Switch the engine OFF. Complete a final inspection of harness routing, plugs, mounting points, connections and fasteners. No road test is part of this procedure.

IMPORTANT

Use the approved Stage 1 schematic for fuse ratings, terminal assignments and circuit verification. The fuel pump is designed to run whenever Key ON is active; an automatic safety cut-off is not included in this revision.